Metallic Epoxy Flooring in Calexico CA - a showpiece floor that stays bonded
Tired of a plain gray slab in the room you show off? We lay a metallic epoxy floor over concrete prepped to hold it.
Request an estimate
Is a metallic epoxy floor right for my room?
Metallic epoxy flooring in Calexico is an epoxy coating mixed with fine metallic or pearlescent pigments. Our crew moves those pigments with rollers, brushes and trowels while the coating is still wet, so the floor cures with a flowing, marbled look no other room will match.
Most people who call about a metallic floor have a room they want to show off, like a finished basement, a home gym, a showroom or a garage that's more display than workshop. One cost guide puts metallic in exactly those rooms and points a daily-use garage with tire marks, dust and dropped tools toward a flake system like our garage floor coatings, and I'd tell you the same, because how the room gets used decides it. The price moves with the size of the room, how much grinding and crack repair your slab needs, whether a slab on the ground needs a moisture barrier and whether you want anti-slip in the top coat. The schedule turns on that same prep plus the cure time between coats, and the written estimate I give you after looking at your floor lays out both.
How we install a metallic epoxy floor
I start every metallic floor by checking the slab for moisture and cracks, and I look hardest at moisture when the slab was poured on the ground, because that's what works a coating loose from below. Then we grind the concrete so the epoxy has something to grip, fill the cracks so they don't show through the pattern, and put down a base coat. The metallic coat goes on next, and our crew works the pigments while it's still wet, since that's the only window you get to set the swirls. A clear top coat goes over it last to take the wear and hold the gloss.
Metallic isn't the answer for every floor, and I'll say so at the estimate rather than sell you the wrong one. If the room takes hot water, spills and hard use, urethane cement flooring stands up to that better, and if you like the look of the concrete itself, polished concrete flooring gives you a glossy floor with no coating on top.
What to know about metallic epoxy flooring in Calexico
In Calexico, the city's Building Division does the plan review and field inspections, and it coordinates permit approvals with other city departments and outside agencies, including the Air Pollution Control District. Whether a metallic floor at your address needs a permit isn't something I'll guess at. If your job needs one, I'll tell you at the estimate, and we'll handle the paperwork with the city or county office that covers your address and book the inspections.
Most of the houses and garages we work on here sit on slabs poured on the ground, and we see the same on jobs in El Centro and Heber, so moisture is the first thing I ask about. Temperature matters too, because one coating maker's instructions call for a floor surface between 50°F and 90°F the whole time and favor coating while the temperature is falling and out of direct sun, so when we start the metallic coat matters as much as how. We're based in Calexico and work in the cities around it, and if you don't see yours on our site, call and ask.
- Call (442) 250-4457
- Mon–Sun: 7 AM–10 PM
- Calexico, CA 92231
What happens when you call Calexico Precision Epoxy Flooring in Calexico?
Call or send us a message
Call (442) 250-4457 or use the form, tell us a little about the room, and we'll get back to you to set a time for me to come out. We take calls seven days a week, 7 AM to 10 PM.
I look over your floor
I check the slab for moisture and cracks, ask how you'll use the room and go over your options with you. You get a written estimate that spells out the prep your slab needs and the price, so you know the number before anything starts.
We prep and coat the floor
Our crew grinds and repairs the concrete, then puts down the base, metallic and top coats in order. Plan to keep people, pets and cars off the floor while each coat cures, because stepping on it early leaves marks you'll see for good.
Walk the finished floor together
When the top coat is down, I walk the floor with you and go over how long to wait before using it and how to keep the gloss. If anything doesn't look right to you, that's the time to say so.
Why Calexico homeowners call us for metallic epoxy floors
I'm on site with the crew
I'm on site with our crew while the work gets done, not just at the estimate. When the metallic coat goes on, the person you talked to is there making the calls, so what you asked for is what goes down.
Time spent under the finish
I learned concrete prep and coatings on other crews before starting this business in 2023, and we're best known for floors that stay bonded because we put the time into the concrete underneath. On a metallic floor that time shows, since any flaw left in the slab shows through the pattern.
Licensed and fully insured, every job
We're licensed and fully insured, and I'm glad to go over that at the estimate before anyone starts work. It means you're hiring a business that answers for the floor, not a crew passing through.
Code questions settled before we start
The same city office also shares information on construction codes, materials and methods, and you can reach it at (760) 768-2105. If you want to check something there before we start, I'd rather you do, because questions are easier to settle before the coating goes down.
A metallic floor is only as good as the slab under it, so the first step is letting me look at yours. Send us a message or call (442) 250-4457.
Request an estimateGet a written estimate for your metallic epoxy floor
Send the form and we'll get back to you within one business day to set up a free on-site estimate, with no obligation. I come out, check your slab for moisture and cracks, talk through what you want from the room and leave you a written estimate.
- Licensed and fully insured.
- Phone
- (442) 250-4457
- Location
- Calexico, CA 92231
- Hours
- Mon–Sun: 7 AM–10 PM
Questions about metallic epoxy floors in Calexico
How much does metallic epoxy flooring cost in Calexico?
Across the US, metallic epoxy flooring usually costs about $6 to $12 per square foot installed, and that's the national market, not our price. One cost guide puts it at roughly double a standard flake system, so the look carries a real premium. Your own number comes in the written estimate once I've seen how much prep your slab needs.
How long does a metallic epoxy floor last in a home?
A professionally installed metallic floor with a quality top coat lasts 10 to 20 years in a home, according to one national cost guide. In a garage, the same guide says to plan on refreshing the top coat every 5 to 8 years to keep the gloss and hide fine scratches.
Is a metallic epoxy floor slippery when it's wet?
It can be, because the finish is smooth and glossy. We can add an anti-slip additive to the top coat, and I'd suggest it for kitchens and garages, where water and spills are part of daily life.
What causes moisture trouble under a metallic epoxy floor?
On a slab poured on the ground, moisture vapor rising through the concrete is the thing to plan for. One coating maker's guide requires a suitable moisture barrier on those slabs, because seasonal changes in ground moisture can push too much vapor through, whatever tests showed before coating. So on a ground-level slab, I don't lean on a single moisture reading when I write your estimate.
How long does each coat of metallic epoxy take to cure?
One maker's guide has the metallic coat cure overnight at 72°F and 50% humidity before the next step, so the room stays closed at least overnight between coats. Heat and humidity shorten how long the mixed coating stays workable, which is why we plan each coat around the room's conditions that day.
How do I get my house ready for a metallic epoxy floor?
Clear the room, and if the product is solvent-based, plan on turning off pilot lights and anything that can spark, such as electric motors, before we start. One maker's data sheet calls solvent-based products extremely flammable and calls for good cross ventilation before installing, so I'll tell you at the estimate which product we're using and what to shut off.
Other floors worth comparing
Urethane Cement Flooring
A good fit for a restaurant kitchen or a shop that sees boiling water, grease and dragged equipment, where a decorative coating would wear out too soon.
Polished Concrete Flooring
Worth a look if you want the shine to come from the concrete itself, with no coating on top that could peel or need recoating down the road.
Tell us about the room you're finishing
Call (442) 250-4457 or use the form with the room's use, its rough size and whether the slab sits on the ground, and I'll know what to test for before I come out.
Request an estimateCall (442) 250-4457